Msd 7805 8-Plus Ignition Control Installation Bedienungsanleitung PDF herunterladen

MSD-8 Plus Ignition

PN 7805

Cylinders Loops to Cut

8 None

6 One

4 Two

2 Three

Cut loops

Remove cap

WARNING: Before installing the MSD Distributor, disconnect the battery cables. When disconnecting

the battery cables, always remove the Negative (-) cable ﬁrst and install it last.

Figure 1 Cylinder Programming.

1 - PN 8830 Filter

1 - Coil Harness

1 - Power Harness

1 - Parts Bag, Mounts, Terminals, etc.

ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered

in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product

will help if there is ever a warranty issue with your product and helps the MSD R&D team create

new products that you ask for! Go to www.msdperformance.com/registration.

Note: Solid Core spark plug wires cannot be used with an MSD Ignition.

Parts Included:

1 - MSD-8 Plus Ignition

1 - Mag Pickup Extension Harness, PN 8860

4 - Vibration Mounts and Hardware

4 - RPM Modules: 3K, 7K, 8K and 9K

FEATURES

SINGLE OR DUAL COIL OUTPUT

The MSD-8 Plus Ignition Control is intended for racing use only. The Ignition has the ability to be

used with single or dual coil systems. Note that when using a single coil, both coil positive wires must

be connected to the coil.

RPM LIMITERS

The MSD-8 Plus Ignition is equipped with a 2-Step Rev Control. The Ignition will accept two rpm

modules so two different rev limits can be set. One rev limit can be used for over-rev protection while

the second limit can be activated on the starting line for a lower rpm limit to assist in staging and for

consistent holeshots. When 12 volts are applied

to the 2-Step terminal (2’S’), Module 1 is active.

Module 2 is active when there is no 12 volts.

CYLINDER SELECT

This ignition can be used on 2, 4, 6 (even-ﬁre)

or 8-cylinder engines. The ignition is set for

8-cylinder operation. To program the unit for

other engines, remove the one screw that holds

the cover to reveal three wire loops (Figure

1). Cutting a wire loop determines the cylinder

selection.

SPARK LED

When the coil ﬁres, current is sensed and this LED will ﬂash. These LEDs conﬁrm that the ignition

has received a trigger signal and that the ignition is working properly. Each time a coil ﬁres, current

is sensed and the corresponding LED will ﬂash. (If the coil is not connected, the LED will not ﬂash.)

When the engine is running, it will appear solid.

M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 ) 8 5 7 - 3 3 4 4

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - MSD-8 Plus Ignition

MSD-8 Plus IgnitionPN 7805Cylinders Loops to Cut8 None6 One4 Two2 ThreeCut loopsRemove capWARNING: Before installing the MSD Distributor, disconnect

Seite 2 - MOUNTING

2 INS TAL LAT ION INS TRU CTI ONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 )

Seite 3 - GENERAL WIRING INFORMATION

INS TAL LAT ION INS TRU CTI ONS 3M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 )

Seite 4 - TROUBLESHOOTING

4 INS TAL LAT ION INS TRU CTI ONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 )

Seite 5 - CHECKING FOR SPARK

INS TAL LAT ION INS TRU CTI ONS 5M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 )

Seite 6

6 INS TAL LAT ION INS TRU CTI ONSM S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 )

Seite 7

INS TAL LAT ION INS TRU CTI ONS 7M S D • W W W . M S D P E R F O R M A N C E . C O M • ( 9 1 5 ) 8 5 7 - 5 2 0 0 • F A X ( 9 1 5 )

Seite 8 - Limited Warranty

ProgrammableDIGITAL-7 PLUSLT BLUEGREENTO CAM SYNCPICKUPGREENPN 8860HARNESSGREENHEAVY BLACK TO BATTERY3 N PIC B APink - Step 1 Retard/Gear 2Violet - St

Kommentare zu diesen Handbüchern

Keine Kommentare

Msd 7805 8-Plus Ignition Control Installation Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Msd 7805 8-Plus Ignition Control Installation herunter. MSD 7805 8-Plus Ignition Control Installation User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Msd 7805 8-Plus Ignition Control Installation