Msd 82933 Modified Distributor Cap and Rotor for Acura Bedienungsanleitung PDF herunterladen

M S D I G N I T I O N • W W W. M SD IG NI TI ON .C OM • ( 91 5) 8 5 7- 52 00 • F A X (9 15 ) 85 7- 33 4 4

Parts Included In This Kit

1 - Distributor Cap

1 - Coil Wire

MSD Modiﬁed Honda Distributor Cap & Rotor

PN 82903, PN 82923 & PN 82933

WARNING: During installation, disconnect the battery cables. When disconnecting the battery

cables, always remove the Negative cable ﬁrst and install it last.

1 - Rotor

1 - Parts Bag

1 - Mini-Stripper-Crimper

Note: The Modiﬁed Cap is designed so that you can remove the stock internal coil, and use a higher output

external coil. The stock internal coil MUST be removed before the installation of this cap. Failure to

do so will cause damage to the MSD cap.

Note: Spark plug style, 90° terminals are required

with this MSD cap.

INSTALLATION:

1. Mark the location of each plug wire on the

distributor cap, then remove the wires. Remove

the stock distributor cap, rotor and dust cover.

2. Locate the coil wires and note their color and

location. On the majority of Honda or Acura

engines, the Black/Yellow wire is positive. The

coil negative wire is generally White/Blue, Blue,

Green/Yellow or Green. In some cases, the coil

itself is marked negative (-) and positive

(+).

Note: If you have a question as to the wires’

polarity, use a volt-meter and probe

each wire with the ignition key turned

to the On position. Coil positive will

show 10-12 volts.

3. Once you determine the polarity of the

coil wires you will need to extend the

wires to reach the MSD external coil. Cut

the factory terminals off and solder them

to 14-gauge wiring. Seal the soldered joint

with shrink sleeve or electrical tape.

4. Depending on the model of distributor

you have, you may need to drill a hole

in the new cap to route the wires out. In

some applications the factory rubber

seal is thick enough to cut and slide the

new wires out.

Figure 1 Primary Wiring with the Coil Removed.

Figure 2 Wiring with a Blaster SS Coil.

ONLINE PRODUCT REGISTRATION: Register your MSD product online and you’ll be entered

in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! Registering your product

will help if there is ever a warranty issue with your product and helps the MSD R&D team create

new products that you ask for! Go to www.msdignition.com/registration.

1 2 3 4

Inhaltsverzeichnis

Seite 1

M S D I G N I T I O N • W W W. M SD IG NI TI ON .C OM • ( 91 5) 8 5 7- 52 00 • F A X (9 15 ) 85 7- 33 4 4Parts Included In This Kit

Seite 2 - TERMINALS

2 INSTALLATION INSTRUCTIONSM S D I G N I T I O N • W W W . M SD IG NI TI ON .C OM • ( 91 5) 8 5 7- 52 00 • F A X (9 15 ) 85 7- 33

Seite 3 - DUAL CRIMP TERMINALS

INSTALLATION INSTRUCTIONS 3M S D I G N I T I O N • W W W . M SD IG NI TI ON .C OM • ( 91 5) 8 5 7- 52 00 • F A X (9 15 ) 85 7- 33

Seite 4

Figure 10 Crimping the Terminal.5. Put the assembly into a vise making sure the alignment tabs are on the outside edge of the vise jaws (Figure 10). 6

Kommentare zu diesen Handbüchern

Keine Kommentare

Msd 82933 Modified Distributor Cap and Rotor for Acura Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Für das Auto Msd 82933 Modified Distributor Cap and Rotor for Acura herunter. MSD 82933 Modified Distributor Cap and Rotor for Acura Integra GSR 94-01 Installation User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Für das Auto Msd 82933 Modified Distributor Cap and Rotor for Acura